Call Now
Same-Day Service - Palm Bay & Brevard County

RV Furnace & Heat Pump Repair - On-Site

RV Repair Palm Bay services RV furnaces, heat pumps, and propane heating systems throughout Palm Bay and south Brevard County. We handle Suburban, Atwood, and Dometic units.

Florida winters are mild but heating systems need to work reliably when overnight temps drop into the 40s - especially for Palm Bay owners who take weekend trips to Sebastian Inlet State Park in January. Same-day service available.

Same-Day Service
|
Palm Bay & Brevard County
|
11+ Years Experience
|
Licensed & Insured
ot
our lead technician  · Lead RV Technician · 11+ years

RV Repair Palm Bay services RV furnaces, heat pumps, and propane heating systems throughout Palm Bay and south Brevard County. We handle Suburban, Atwood, and Dometic units.

Florida winters are mild but heating systems need to work reliably when overnight temps drop into the 40s - especially for Palm Bay owners who take weekend trips to Sebastian Inlet State Park in January. Same-day service available.

RV Repair Palm Bay technician performing RV Heater Repair in Palm Bay, FL

Diagnosing RV Furnace Failures After Palm Bay's Long Storage Season

RV furnace diagnosis in Palm Bay almost always starts the same way: a Palm Bay homeowner fires up the furnace for the first time in October after 7 or 8 months of storage in a hot driveway. The furnace clicks but does not light.

In Palm Bay's storage environment, sustained driveway heat causes igniter tip scaling, thermocouple contact oxidation, and propane regulator diaphragm hardening that does not occur in markets where furnaces run year-round. We start every Palm Bay furnace call with propane pressure verification - low pressure mimics furnace failure and costs nothing to rule out first.

If propane pressure is good, we test the DSI ignition module, igniter, thermocouple, and sail switch in sequence. Palm Bay Suburban SF-30 and SF-42 calls most often resolve at the igniter - scaled from storage heat - or the sail switch, which develops intermittent opens from the same thermal cycling.

Both parts are on the van and replaced in under an hour on most calls. Control board failures are less common but we carry boards for Suburban and Atwood units as backup.

Heat pump diagnosis covers both heating and cooling modes on every call. Palm Bay heat pumps run year-round for cooling, so the reversing valve that enables heating mode can stick in cooling position from infrequent actuation in Palm Bay's mild winters. We test both directions before closing out the job.

Same-day heating service is available throughout Palm Bay - call before mid-morning for afternoon arrival at your driveway.. RV Heating System Repair Cost Guide ServiceTypical CostNotes Service Call + First Hour$299 - $399Travel + diagnosticsFurnace Igniter or Pilot Repair$150 - $300Suburban or Atwood; most common furnace fixThermocouple Replacement$100 - $200Safety sensor; prevents no-heat failuresControl Board Replacement$250 - $550Furnace or heat pump control boardFurnace Blower Motor Replacement$200 - $400Suburban or Atwood blower assemblyHeat Pump Service (Dometic/Coleman Mach)$200 - $500Diagnosis, coil clean, and refrigerant check Pricing note: Ranges shown are average costs for the Palm Bay, FL market based on common repair scenarios.

A written estimate is provided before any work begins - you approve it before we start.

What to Expect at Your Palm Bay Heating Service Call

We arrive with a combustion analyzer, multimeter, and furnace parts stocked for Suburban and Atwood units - the two brands covering roughly 80% of RV furnaces we see in Brevard County. We start with propane pressure at the regulator before touching the furnace, because low propane pressure mimics a furnace failure and costs nothing to rule out first.

If propane pressure is good, we test the igniter, thermocouple, limit switch, and sail switch in sequence. Palm Bay furnace calls tend to come after the rig has sat in driveway storage all summer - igniters scale from long-term heat exposure and sail switches develop intermittent opens from the same heat cycles. Both parts are on the van and replaced in under an hour on most calls.

Control board failures are less common but we carry boards for Suburban and Atwood units. Heat pump diagnostics take slightly longer because they involve both electrical and refrigerant circuits. We test both heating and cooling modes on every heat pump call before we sign off.

Palm Bay heating calls come from homeowners who last ran the furnace in February and are now heading to Sebastian Inlet State Park in December. A furnace that sat all summer in a hot driveway sometimes reveals igniter or gas valve issues that were not apparent before storage. We prioritize heating calls the same as AC calls - same-day service, written estimate first.

Palm Bay and South Brevard County RV Heating Conditions

Palm Bay winters are mild, but cold snaps dropping overnight temperatures into the 30s occur from December through February - often when Palm Bay homeowners have scheduled a winter trip to Sebastian Inlet State Park or the Florida Keys. Heating systems that sit unused from March through November in a hot driveway develop specific issues: igniters accumulate a scale layer from long-term heat exposure, thermocouple contacts oxidize, and propane regulators can develop diaphragm stiffness from UV and heat.

We recommend firing your furnace for 15 minutes in October before the first cold snap to verify it lights and holds a flame before you need it at midnight. Heat pump systems are easier on the furnace - they handle the mild Florida shoulder-season temps, so the furnace only runs on truly cold nights and stays in better condition between seasons.

How We Diagnose Your RV Heating System Repair

From your first call to a repaired RV - here is what to expect.

Call and describe the heating symptom
Tell us whether the furnace is not igniting, blowing cold, or running but not heating. We load the right furnace parts before we leave.
We arrive at your Brevard County location
No towing required. Your tech drives to you in Palm Bay, Melbourne, Cocoa, or anywhere else in Brevard County.
On-site diagnosis of the heating system
We check the igniter, thermocouple, limit switch, and control board to isolate the fault before recommending any work.
Written estimate, then same-visit repair
You approve the price first. Most Suburban and Atwood furnace repairs are completed the same visit with parts on the van.

Warning Signs for Palm Bay RV Heating Systems

The furnace clicks 3 or 4 times but never lights when you first fire it up in October

This is the number-one Palm Bay furnace symptom. After 7 or 8 months of storage in a hot driveway, igniter scaling prevents the arc from jumping reliably. If it did not light in the first 3 tries, call before you need it in the cold.

The furnace lights but shuts off within 30 seconds

The sail switch or limit switch is failing. Palm Bay furnaces that sat in a hot driveway all summer develop switch contacts that oxidize and cause intermittent opens - it appears to light but cannot sustain the flame.

You smell propane from the furnace area but the furnace does not light at all

Shut off propane immediately. This indicates a gas valve that is not closing fully or a cracked burner orifice. Do not attempt to relight until a technician has inspected the system.

The blower runs for 3 or more minutes before the burner lights

Normal pre-purge is 30 to 45 seconds. Extended purge indicates a sail switch that is not reading adequate airflow - often from a dirty or partially blocked duct in a rig that sat closed all summer.

The heat is uneven - warm from one vent, room temperature from another

A partially collapsed duct or closed damper, or a blower motor that is not reaching full speed from brush wear. Palm Bay furnaces that are only run for the Florida winter season see less blower wear, but brush corrosion from storage humidity can mimic the same symptom.

Your heat pump runs in heating mode but blows cool air when it is 45 degrees outside

Heat pumps cannot extract enough heat from air below 40 to 45 degrees. This is not a failure - below that threshold the furnace should take over. If it is 55 degrees and the heat pump is not heating, there is a reversing valve issue.

A rattling or vibrating sound from the furnace cabinet during operation

A loose blower wheel, a cracked mounting bracket, or a panel that has been worked loose by heat cycling during summer driveway storage. All diagnosable on-site.

RV Heating Brands We Service in Palm Bay

Palm Bay furnace service is dominated by two brands and one failure cause: Suburban and Atwood furnaces failing after long summer storage. Suburban SF-30 and SF-42 are the most common in Palm Bay towable RVs - after 7 or 8 months of storage in a hot driveway, the DSI ignition board contacts oxidize and the igniter tip scales.

Palm Bay Suburban calls are most often igniter replacements and board swaps, both stocked on the van. Atwood 8500 IV and 8535 IV units stored in Palm Bay's summer heat develop limit switch failures at higher rates than in cooler-climate storage - the limit switch bimetal element fatigues from repeated heat cycling even when the furnace is not running.

Dometic Comfort Control heat pumps on higher-end coaches stored in Palm Bay driveways have a reversing valve that benefits from occasional winter use - Palm Bay's mild winters mean some owners never run the heat pump, and the reversing valve sticks in cooling mode from infrequent actuation. We carry Suburban and Atwood furnace parts on the van for same-day service throughout Palm Bay and south Brevard County.

RV Heating Service in Palm Bay's Seasonal-Use Pattern

RV furnaces in Palm Bay face a specific challenge: extended inactivity. Palm Bay's mild climate means furnaces that run regularly from October through February in northern markets sit completely unused from March through November here. Eight months of storage in a hot driveway creates igniter scaling, thermocouple oxidation, and propane regulator diaphragm hardening that does not occur in markets where the furnace runs at least periodically through the year.

The October test run is the single most valuable furnace maintenance step for Palm Bay homeowners. Before the first cold snap - typically in late October or early November - run the furnace for 15 minutes with the rig plugged in and the thermostat set high.

If it ignites and holds a flame, the igniter, thermocouple, and gas valve are functional. If it clicks but does not light, the igniter has scaled during the summer storage period and needs cleaning or replacement before you need it at Sebastian Inlet in January.

Heat pump systems are more forgiving than furnaces in Palm Bay's climate because they run year-round for cooling - the reversing valve that makes them heat is exercised regularly on the same system that provides air conditioning. Palm Bay homeowners with heat pump-equipped rigs typically see fewer cold-snap furnace surprises than those with propane furnace-only systems. We always test both heating and cooling modes on heat pump service calls to confirm the reversing valve works in both directions before closing out the job.

For winter trips from Palm Bay to Sebastian Inlet State Park or down the Keys, Florida winter nights can drop below 50 degrees with no warning - especially in January and February. An RV furnace that passed the October test may still develop a sail switch intermittent during cold snaps if the blower runs at high speed in cold air. If your furnace lights but shuts off after 30 seconds in cold weather, call us - same-day heating service is available from Palm Bay year-round.

RV Heating System Repair FAQ

My Palm Bay RV furnace clicks but won't light after sitting all summer. What should I do?

Check the propane level first - low propane mimics furnace failure. If the propane level is good, the most likely cause is igniter scaling from 7 to 8 months of storage heat in a Palm Bay driveway. The igniter tip accumulates a scale layer from sustained heat that prevents the arc from jumping reliably to the burner.

This is a same-day repair - we carry igniters for Suburban and Atwood units on the van. Do not attempt to run the furnace repeatedly if it does not light in 3 tries - call for service.

My RV furnace lights but shuts off within 30 seconds. What is the cause in Palm Bay's climate?

The sail switch or limit switch is the most likely cause after Palm Bay summer storage. Palm Bay furnaces that sit unused through the hot summer develop switch contacts that oxidize and cause intermittent opens.

The furnace lights but cannot sustain the flame because the sail switch opens under normal blower pressure, or the limit switch trips from a heat buildup caused by restricted airflow through ducts that have been closed all summer. Both are on the van for same-day replacement.

How do I prepare my Palm Bay RV furnace for the winter before a Sebastian Inlet trip?

In October, before the first cold snap, run the furnace for 15 minutes with the rig plugged in and the thermostat set high. If it ignites and holds a flame, the igniter, thermocouple, and gas valve are functional for the season.

If it clicks but does not light, schedule a service call before the trip. A Palm Bay furnace that last ran in February and sat in a hot driveway through summer may have igniter or sail switch issues that only show when you need heat at Sebastian Inlet at midnight in January.

What does RV furnace repair cost in Palm Bay?

The service call is $299 to $399 covering travel to your Palm Bay location and the first hour of diagnostics. Igniter or sail switch replacement is $150 to $300. Thermocouple replacement is $100 to $200.

Control board replacement runs $250 to $550 depending on the brand. Most Palm Bay furnace calls resolve at the igniter or sail switch - both are same-day repairs.

My Palm Bay RV has a heat pump instead of a furnace. How is that different to maintain?

Heat pumps in Palm Bay run year-round for cooling, so the reversing valve that enables heating mode gets exercised on the same system. This is an advantage - Palm Bay heat pump owners see fewer no-heat surprises than those with propane-only furnaces.

The main failure mode specific to Palm Bay heat pumps is the reversing valve sticking in cooling position if the owner never runs the system in heating mode through the mild fall. We test both heating and cooling modes on every heat pump service call.

Can you repair my RV furnace at my Palm Bay driveway?

Yes. We come to your Palm Bay driveway with a combustion analyzer, multimeter, and furnace parts stocked for Suburban and Atwood units.

Most Palm Bay furnace calls are completed on-site the same day. Same-day heating service is available throughout south Brevard County - call before mid-morning for afternoon arrival.

What furnace brands do you service in Palm Bay?

Suburban and Atwood cover approximately 85% of the RV furnace market in Palm Bay. Suburban SF-30 and SF-42 and Atwood 8500 IV and 8535 IV are the most common. We also service Dometic Comfort Control heat pumps and Coleman Mach heat pump units.

Parts for Suburban and Atwood are stocked on the van for same-day service. Heat pump refrigerant components are sourced within 1 to 2 business days.

My Palm Bay RV furnace produces uneven heat - warm from one vent, room temperature from another. What causes that?

A partially collapsed or disconnected duct, a closed duct damper from a past service, or a blower motor that is not reaching full speed. In Palm Bay rigs that sit closed all summer, ducts sometimes collapse where they run through tight compartments due to heat and lack of airflow.

We trace the duct run from the furnace blower to each vent outlet to identify where the restriction is. This is a same-day diagnostic.

What temperature does my Palm Bay RV heat pump stop working effectively?

Heat pumps cannot extract sufficient heat from air below 40 to 45 degrees. In Palm Bay, overnight temperatures drop below 45 degrees roughly 10 to 20 nights per year, mostly in January and February.

On those nights, the furnace backup should take over automatically. If your heat pump system does not have a propane furnace backup, it will only provide minimal heat on cold Palm Bay nights - this is a system design question, not a failure.

How do I know if my Palm Bay RV furnace is safe to operate after long storage?

The October test run described above tells you if the furnace lights and holds a flame. For propane system safety, check for gas odor around the regulator and propane lines before running the furnace. No propane smell, lights on first attempt, holds a flame for 5 or more minutes - the system is functional.

Propane smell, no light, or flame that extinguishes quickly - call before using the furnace. Annual LP system inspection is part of every Palm Bay pre-trip check.

Need RV Heater Repair in Palm Bay?

Same-day mobile service throughout Palm Bay and Brevard County. Written estimate before any work starts.